How to clean grease trap

How often should grease traps be cleaned?

How often should grease traps be cleaned? The frequency of restaurant grease trap cleanings vary with how often the kitchen produces FOGS. On average, cleanings should be performed every one to three months.

What do you use to clean out a grease trap?

Next, refresh the grease trap and free the tank from obnoxious odors with a little elbow grease, a steel pot scrubber, dish soap and tepid water. Thoroughly scrub down the grease trap’s baffles, sides and lid. Flush out the soap and debris a few times using clean water.

Should a grease trap be full of water?

When grease is 25% or more the total liquid depth.

If the container is filled with a surplus of fats, oil, and grease, important processes and functions may get interrupted or slowed down in your commercial kitchen. In fact, cleaning a grease trap that is 25% full is an EPA rule; for health and safety reasons.

How do you know when a grease trap is full?

Poorly maintained grease trap leads to clogged drains. When the fat, oil, and grease, which the grease trap catches, builds up and solidifies, water flowing to the sewer slows down. If you notice your sink draining slowly, check if your grease trap is full or clogged. It’s a sign that your grease trap needs cleaning.

Does vinegar break up grease?

Vinegar’s acidity helps cut through grease easily. Spray some vinegar and water mix onto a splattered stovetop, let it sit for 10 minutes, and then scrub down with soapy water. It should wipe right off.

How do I fix a smelly grease trap?

You can try:

  1. Pouring a drain cleaner down the kitchen sink.
  2. Pump out the grease trap.
  3. If the smell persists, Lee’s Environmental offers jet rodding which is high pressure drain cleaning to clean the pipes from the grease trap inlet to the kitchen.

What can I do with an old grease trap?

Dispose of grease trap contents in a sealed container and dispose of sealed container in the trash. Do not pour grease down drains, toilets or the storm drain system.

How do you neutralize grease?

Rapinchuk says a simple mix of baking soda, kosher salt and dish soap will do the trick on cooked-on food stains and grease. Use a kitchen scrub brush to work into the little nooks. Rise and dry parts, then reassemble.

How much does it cost to clean a grease trap?

Indoor Grease Trap Cleaning Cost

The cost to pump and clean a indoor grease trap that has been maintaned reguarly can average from $175 – $475. Grease traps that have not been serviced and maintained regularly can cost up to triple the normal price.

Can you put Drano in a grease trap?

To combat this problem, many turns to using chemicals such as Liquid Plumber or Drano to clear these clogs. Others add bacteria or enzymes to their grease traps hoping these products will eat and break down these food solids.

What size grease trap do I need?

For machines with a 10-15 gallons capacity, use a grease trap that can handle at 15 pounds or higher. 20 to 30 gallons require a grease trap that can handle at least 20 pounds.

How does a grease trap work in a commercial kitchen?

Grease traps are devices that your kitchen wastewater flows through on the way to the sewer. As your kitchen wastewater flows through the first chamber, it captures the grease. Once it solidifies, it will float to the top of the first chamber, allowing the clean water to flow into the second chamber.

Why does a grease trap smell?

While a grease trap separates the FOG from the wastewater, some food particles and organic solids are trapped inside, eventually settling to the bottom of the tank. The sulphuric gases are responsible for producing the foul smell inside the grease trap.

What is fog in grease trap?

FOG: Fats, Oils, Greases

The ”stuff” that collects inside your grease trap is referred to as FOG, and if not properly managed, it can have serious consequences for your pipes, the local sewer system and the environment. What Is FOG? Grease trap FOG refers to fats, oils and greases.

How does a residential grease trap work?

A grease trap works by cooling warm or hot greasy water. Vegetable oils and animal fats are 10 to 15% less dense than water and are insoluble in water. By allowing the fats, oils, and grease to cool, the different layers of the mixture are able to separate into individual layers for easy separation.

Why do some houses have grease traps?

To be more precise, a grease trap is essentially a plumbing device that is meant to trap grease and other build-up from entering the wastewater disposal system. Grease traps are critical for preventing clogs and other plumbing damages from happening, specifically concerning grease.

Where do grease traps go?

There are two primary types of grease traps. Interior traps are usually located in the kitchen area near the sink or dishwasher, and tend to hold smaller amounts of FOG. Exterior traps are located outside your building, underground. Exterior traps are much larger, holding thousands of gallons.

Where is a grease trap usually installed?

Hydromechanical grease interceptors (commonly called grease traps) are usually installed underneath the 3 compartment sink or in the floor of the kitchen. They trap grease over time and need to be pumped frequently, sometimes even weekly.

How long does it take to install a grease trap?

The average installation time will vary. However, one can normally expect less than two hours from start to finish.

How often do you pump a grease trap?

A good rule of thumb for any cleaning schedule is every one to three months. However, in order to determine if it should be one or three, you will need to follow the 1/4th rule. This rule states that once 1/4th of your grease trap has been filled with fats, oils, grease, and solids (FOGS) it is time for a pump out.

How much does a 1000 gallon grease trap cost?

The cost for having a 1000 – 1500 gal grease trap is between $225 – $315 per pumping, assuming that you sign up for an extended service program with a given grease hauler.

How much does a 1500 gallon grease trap weigh?

Top to Center of Inlet 14″ Top to Center of Outlet 16″ Weight 2800 Lbs.

How much does a 1500 gallon grease interceptor cost?

The average cost for the installation of a new grease trap (750 to 1500 gallons) is between $4000 and $8500.

What is grease trap in restaurants?

Grease interceptors are large in-ground outdoor tanks that prevent FOG and food solids from entering the sanitary sewer or septic system at restaurant facilities. Conventional Grease Traps are referred to as passive grease traps and gravity based grease traps. Grease Traps were originally designed over 100 years ago.

How to clean grease trap

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Scroll to top