Protection Status

Home for Latest News and General Updates

How to install a hardtail guitar bridge


Jan 29, 2024
Spread the love

How do you set up a hardtail bridge?

Can you put a hardtail bridge on a Strat?

You can get a generic hardtail bridge, just make sure the string spacing at the bridge is the same as the old one. It won’t screw up anything but the strings will lay funny if the width at the bridge doesn’t match.

How does a hardtail bridge work?

Also known as hardtails, fixed bridges are screwed into the body of the guitar and keep the strings in place resting on saddles. Each end runs from the body up to the headstock. Strings come standard with ball ends, so naturally, the fixed bridge will accommodate their functionality.

How do you install a guitar bridge?

Where should a guitar bridge be placed?

In order to place the bridge saddles in the correct location, you’re going to have to hold the ruler on the 12th fret (on the actual metal fret, not in between the two) & then measure the distance from here to the inside of the guitar nut at the top of the neck, where it meets the wood.

How much does it cost to repair a guitar bridge?

Depending on your location a bridge reglue should run between 70 to 100 bucks. The higher prices are probably including a setup charge. Regluing a bridge is not rocket science but does need to be done by an experienced shop. Cost should be around $80-$110 including setup.

Can you fix a broken guitar bridge?

If your bridge is loose or cracked, you will need to remove it from the body and re-glue it or replace it. Take a look at the back of the bridge. Can you see a gap in between the bridge and the body? If so, it has come loose.

What is the best glue for guitar bridge repair?

Regluing and Clamping The Bridge

Once sure that the bridge is well mated to the top, it is ready to be glued into position. We typically prefer titebond as the glue of choice because it has a reasonably long open time, is fairly easily removed if necessary, and it is easy to apply and cleanup.

How do you reattach a guitar bridge?

What causes guitar belly bulge?

Sometimes acoustic guitars develop a bit of a belly. Over time the string tension pulls on the bridge, angling it forward and warping the top, which in turn raises the action and causes other structural problems down the line. To fix this we have to remove the bridge and address the top directly.

How do you glue a guitar bridge?

Why is my guitar bridge raised?

If you put a new set of strings but in a heavier / thicker gauge, the overall tension of strings when tuned up will be higher, thus resulting in a raised bridge. In order to fix this problem, you can open the backplate of your guitar and inspect the springs.

Should a Strat bridge be flat?

Some players prefer to have the bridge sit flat on the body, for maximum vibration transfer and so that the guitar doesn’t go out of tune if a string breaks. Other players like the bridge just slightly off the body so that the arm can be used to make notes/chords slightly sharp and flat for vibrato.

How high should my floating bridge be?

Fender recommends the bridge height be 1/8th of an inch above the body.

How do you set up a floating bridge?

Does David Gilmour use a floating bridge?

According to, David Gilmour uses his bridge flat against the body. It does not float. He only uses the trem bar to go down.

Do Fender Strats have floating bridges?

If you are adjusting a Fender Strat-style guitar with a floating bridge, this is the point at which you will balance the trem so that the strings will pull the bridge base off of the body. When you float the bridge, you are essentially putting the trem springs in the mix. There is definitely a tone in that.

What is the point of a floating bridge guitar?

What is a Floating Bridge? Floating bridges are also known as tremolo bridges. They do what fixed bridges, in that they provide an end-point for the strings on the guitar’s body, but they also have an additional function that fixed bridges can’t do.

Is a tremolo bridge worth it?

it’s worth it if you use one, it’s not if you don’t. it’s pretty much as simple as that. EDIT: just make sure you don’t get a crap quality locking (or non-locking, but especially locking, as some of the cheapo licensed floyds are horrendous and may put you off trems for life!) trem.

Should I float my bridge?

You should have ZERO tuning issues that way, and the tone may even be more to your liking. Floating trems are nice, but if you do unison bends or anything like that, the bridge will move every time you bend and it will be hard to play in tune. Breaking a string will also cause things to go out of whack a bit.

By admin